manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–918

1.

Check the installation of the exhaust gas temperature sensor
(burner outlet).

2.

Make sure there is no dirt or damage to the exhaust gas tempera-
ture sensor (burner outlet).

NO

YES

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the exhaust gas temperature sensor (burner outlet)
connector.

3.

Use the electrical tester to measure the resistance between the
terminals of the exhaust gas temperature sensor (burner outlet).

NO

YES

11

Inspect the exhaust gas temperature sensor (burner outlet)

Was any failure found?

Clean the exhaust gas temperature sensor
(burner outlet) and install it properly.
If damaged, replace the exhaust gas temper-
ature sensor (burner outlet).
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 12.

12

Inspect the exhaust gas temperature sensor (burner outlet) unit

DIT-

DIT+

SAPH16F010300721

Measurement

conditions

Tester connections

Standard values

Starter switch: 
LOCK

Exhaust gas tem-
perature sensor 
(burner outlet)
DIT+ 

–

 DIT-

0.3 

–

 1.8 

Do the measurements meet the standard value?

Replace the BCU.
Perform "After-inspection work" of INFOR-
MATION section.

Replace the exhaust gas temperature sensor
(burner outlet).
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Daihatsu S85 Wiring Diagrams preview
S85
Brand: Daihatsu Pages: 41
Daihatsu S85 Workshop Manual preview
S85
Brand: Daihatsu Pages: 268
GMC SIERRA 2002 Manual preview
SIERRA 2002
Brand: GMC Pages: 499
Kia Amanti Owner'S Manual preview
Amanti
Brand: Kia Pages: 290
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Brand: Scosche Pages: 16
TATA Motors TIGOR EV 2021 Owner'S Manual preview
TIGOR EV 2021
Brand: TATA Motors Pages: 236
Motoalliance Denali MA11705 Manual preview
Denali MA11705
Brand: Motoalliance Pages: 5
Camoplast T4S Installation Manuallines preview
T4S
Brand: Camoplast Pages: 19
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Brand: E&G Classics Pages: 4
Honda Civic Hatch 2017 Owner'S Manual preview
Civic Hatch 2017
Brand: Honda Pages: 687
Vauxhall 2013 Zafira Tourer Owner'S Manual preview
2013 Zafira Tourer
Brand: Vauxhall Pages: 289
Ecco Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600 Manual preview
Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600
Brand: Ecco Pages: 2
NanoCam Plus NANO CONNECT Smartview 72 Quick Start Manual preview
NANO CONNECT Smartview 72
Brand: NanoCam Plus Pages: 4
Fab Fours Z1550 Installation Manual preview
Z1550
Brand: Fab Fours Pages: 18
Macally HRMOUNTPROTRAY User Manual preview
HRMOUNTPROTRAY
Brand: Macally Pages: 19
TAUBENREUTHER 2360-00 Manual preview
2360-00
Brand: TAUBENREUTHER Pages: 10
ADAPT SOLUTIONS XL-SEAT XLS-DAKC05L Installation Manual preview
XL-SEAT XLS-DAKC05L
Brand: ADAPT SOLUTIONS Pages: 9
ADAPT SOLUTIONS XL-Seat XLS-DAKQ05R Installation Manual preview
XL-Seat XLS-DAKQ05R
Brand: ADAPT SOLUTIONS Pages: 11

Brands by name

Popular brands

Load more brands