manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1107

1.

Check the installation of the air flow sensor.

2.

Make sure there is no dirt or damage to the air flow sensor.

NO

YES

1.

Check the connection of the air flow sensor connector (Looseness
and poor contact).

NO

YES

1.

Check the air intake system (between air cleaner and diesel throt-
tle) for dirt, clogging, or damage.

NO

YES

4

Inspect the air flow sensor

Was any failure found?

If dirt, clogging or damage was found,
replace the sensor.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 5.

5

Inspect the air flow sensor connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 6.

6

Check the air intake system

Was any failure found?

Clean or replace.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 7.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Brand: Suzuki Pages: 16
Jeep Renegade Owner'S Handbook Manual preview
Renegade
Brand: Jeep Pages: 212
Harbor Freight Tools 92043 Assembly And Operating Instructions preview
92043
Brand: Harbor Freight Tools Pages: 4
Yakima Q46 Installation Instructions preview
Q46
Brand: Yakima Pages: 4
Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 2
Yakima K1005 Instructions Manual preview
K1005
Brand: Yakima Pages: 12
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Brand: FABBRI PORTATUTTO Pages: 2
CITROEN C8 NaviDrive Manual preview
C8 NaviDrive
Brand: CITROEN Pages: 52
Masterack RM470057 Assembly Instructions preview
RM470057
Brand: Masterack Pages: 4
Over Armour Offroad KAW-SX-SDK01 Instructions For Installation And Care preview
KAW-SX-SDK01
Brand: Over Armour Offroad Pages: 5
WABCO TP19108 Installation Manual preview
TP19108
Brand: WABCO Pages: 32
Menabo JUZA Fitting Instructions Manual preview
JUZA
Brand: Menabo Pages: 12
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Brand: STO N SHO Pages: 7
JANE StrataPlatform Instructions Manual preview
StrataPlatform
Brand: JANE Pages: 58
Road Ranger H392 Installation Manual preview
H392
Brand: Road Ranger Pages: 22
FALCON RIDGE HU-4421-XL-SDK01 Instructions For Installation And Care preview
HU-4421-XL-SDK01
Brand: FALCON RIDGE Pages: 5
Dodge 2005 JR41 Stratus Owner'S Manual preview
2005 JR41 Stratus
Brand: Dodge Pages: 293
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Brand: Mynew Pages: 5

Brands by name

Popular brands

Load more brands