manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–130

INSPECTION PROCEDURE: P2048

1.

Check the connection of the DEF injector connector (Looseness
and poor contact).

NO

YES

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the DEF injector connector.

3.

Use the electrical tester to measure the resistance between the
terminals of the DEF injector.

NO

YES

1

Inspect for short-circuit in the DEF injector harness

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

2

Inspect the DEF injector unit

DMH

DML

SAPH16F020400084

Measurement 

conditions

Tester 

connections

Standard values

Starter switch: 
LOCK

DEF injector
DML 

–

 DMH

20 

C {68 

F}:11.4 

–

 12.6 

Do the measurements meet the standard value?

Go to step 3.

Replace the DEF injector.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Lancia Y Owner'S Handbook Manual preview
Y
Brand: Lancia Pages: 191
PAC I GM3 Instruction Manual preview
I GM3
Brand: PAC Pages: 15
VanEssa mobilcamping V1 User Instruction preview
V1
Brand: VanEssa mobilcamping Pages: 8
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Brand: BrandMotion Pages: 8
Velleman CAMCOLC1N User Manual preview
CAMCOLC1N
Brand: Velleman Pages: 6
U.S. General 95904 Operating Instructions preview
95904
Brand: U.S. General Pages: 4
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Brand: Safe Fleet Pages: 12
TATA Motors 2013 Nano Owner'S Manual preview
2013 Nano
Brand: TATA Motors Pages: 136
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Brand: U.S. General Pages: 8
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Brand: H&S Pages: 32
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Brand: Valeo Pages: 25
Sanitas SMG 245 Instructions For Use Manual preview
SMG 245
Brand: Sanitas Pages: 36
Skoda KAROQ 2017 Owner'S Manual preview
KAROQ 2017
Brand: Skoda Pages: 324
Audi Audi 80 1987 Workshop Manual preview
Audi 80 1987
Brand: Audi Pages: 63
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Brand: IOGear Pages: 38
TOGU Airgo Active cushion / Comfort Manual And Maintenance Instructions preview
Airgo Active cushion / Comfort
Brand: TOGU Pages: 2
Ford 2003 Mustang Workshop Manual preview
2003 Mustang
Brand: Ford Pages: 4378
Toyota 2013 Prius c Owner'S Manual preview
2013 Prius c
Brand: Toyota Pages: 549

Brands by name

Popular brands

Load more brands