Hino 238 Workshop Manual Download Page 28

Page: 28 / 919

ENGINE CONTROL SYSTEM (J08E)

4–805

Connect the PTO accelerator sensor connector.

Use the electrical tester to measure the resistance between the
terminals of the engine ECU (signal check harness).

YES

Connect the vehicle to Hino-DX.

Set the starter switch to the "ON" position.

Select [Engine] and check if P1133 has been detected in [Fault
Information].

YES

Inspect disconnection of the PTO accelerator sensor harness

V45

V68

V71

V68

SAPH16F010300646

Measurement

conditions

Tester connections

Standard values

Starter switch:
LOCK

Engine ECU (signal
check harness)
ASCS(V68)

–

AVC5(V71)

ASCS(V68)

–

ADG7(V45)

More than 2



Do the measurements meet the standard value?

Go to step 6.

Repair or replace the harness.
Perform "After-inspection work" of INFOR-
MATION section.

Check the DTC detected (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300647

Has DTC P1133 been detected?

Replace the engine ECU.
Perform "After-inspection work" of INFOR-
MATION section.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands