manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1285

1.

Check the sensor system again (steps 15 

–

 18).

NO

YES

1.

Perform an SCV test and a malfunction reproduction test.

•

For a detailed procedure, refer to the separate "SCV free acceler-
ation test".

2.

Compare the test results with those obtained in step 4 and check if
they improved.

NO

YES

25

Check again the sensor system

Was any failure found?

Repair or replace the faulty part, and go to
step 26.

Go to step 26.

26

SCV free acceleration test [Hino-DX]

Select

Engine

SAPH16F010301009

Did the test results improve?

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Contact the Hino national service manager.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Brand: Jeep Pages: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Brand: Jeep Pages: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Brand: Jeep Pages: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Brand: Jeep Pages: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Brand: Jeep Pages: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Brand: Jeep Pages: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Brand: Jeep Pages: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Brand: Jeep Pages: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Brand: Jeep Pages: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Brand: Jeep Pages: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Brand: Jeep Pages: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Brand: Jeep Pages: 4
Jeep Jeep Wrangler Owner'S Manual Supplement preview
Jeep Wrangler
Brand: Jeep Pages: 50
Jeep Grand Cherokee SRT 2014 Owner'S Manual preview
Grand Cherokee SRT 2014
Brand: Jeep Pages: 118
Jeep 2014 Grand Cherokee Accessories Quick Reference Manual preview
2014 Grand Cherokee
Brand: Jeep Pages: 24
Jeep Grand Cherokee Specfications preview
Grand Cherokee
Brand: Jeep Pages: 8

Brands by name

Popular brands

Load more brands