Hino 238 Page 867 Workshop Manual Download

Page: 867 / 919

DEF SCR SYSTEM (DCU)

5–301

CHECKLIST: P2203

DTC: P2203

NOx sensor (SCR upstream) and Heater

- Circuit (Circuit short)

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

Check the
DTC detected
(DCU) [Hino-
DX]

Check if a CAN communication
system malfunction (U029D) has
been detected in [DCU].

DTC P029D
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Go to the diag-
nostic proce-
dure of a
related DTC.

Replace the
NOx sensor 1
(SCR
upstream).
Perform "After-
inspection
work" of
INFORMA-
TION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands