Hino 238 Page 751 Workshop Manual Download

Page: 751 / 919

DEF SCR SYSTEM (DCU)

5–185

DTC: P208A

EN01H16F02040F03001039

DTC: P208A DEF pump motor - circuit (Open load)

INFORMATION

1. Technical description

•

DCU determines failure of DEF pump motor based on DEF pump circuit voltage.

<Description of malfunction>

•

Actuator malfunction of DEF pump module is detected.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.
DEF pump module actuator Duty cycle

0 %

(2) Judgement criteria

DEF pump module actuator voltage is in 2.7 V to 5 V range for 2 sec. or more.

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

SCR System failure lamp: ON

•

DEF injection is stopped.

•

NOx purification function is stopped.

•

If malfunction does not improve within 500 miles: engine output is restricted.

•

If malfunction does not improve within 2,000 miles: vehicle speed is restricted.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Exhaust gas purification function has deteriorated.

•

Engine output is insufficient (when malfunction does not improve within 500 miles)

•

Vehicle does not speed up (when malfunction does not improve within 2,000 miles)

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

Supply module

(DEF pump)

DCU

LFQ

(PSR+)

LFR

LGD

(PSRS)

(PSR+)

(PSRS)

LFP

LGF

(PSR-)

LFJ

(PMP+)

LFL

LG8

(PMPS)

(PMP+)

(PMPS)

LFK

LGA

(PMP-)

LFM

LGB

(PMV+)

LFN

LGC

(PMV-)

LGE

LG9

SAPH16F020400119

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands