manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–63

DTC: P062F

EN01H16F02040F03001017

DTC: P062F Controller store data error

INFORMATION

1. Technical description

•

DCU internal ROM is being checked in DCU.

<Description of malfunction>

•

DCU internal malfunction has been detected.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.

(2) Judgement criteria

DCU internal chip errors are judged by DCU itself.

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

DEF injection is stopped.

•

NOx purification function is stopped.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Exhaust gas purification function has deteriorated.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

8. Estimated failure factors

•

DCU malfunction

NOTICE

• If the DCU power supply is shut off forcibly, such as by disconnecting the battery before the pump operation

ends, and the DCU main relay turns off after the starter switch is turned OFF, P062F may be detected.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Daihatsu G200 Service Manual preview
G200
Brand: Daihatsu Pages: 485
FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Brand: FANATEC Pages: 9
Yakima K618 Instructions Manual preview
K618
Brand: Yakima Pages: 11
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Brand: Safe Fleet Pages: 12
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Brand: Lincoln Pages: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Brand: Volkswagen Pages: 26
SAF-HOLLAND FleetMaster Air FW8 Series Owner'S Manual preview
FleetMaster Air FW8 Series
Brand: SAF-HOLLAND Pages: 20
Farad BARS PR25 - 2 Quick Start Manual preview
BARS PR25 - 2
Brand: Farad Pages: 8
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Brand: GMC Pages: 425
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Brand: Cadillac Pages: 34
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Brand: Scosche Pages: 16
Yakima Landing Pad 24 Quick Start Manual preview
Landing Pad 24
Brand: Yakima Pages: 11
Fast Master Products SWIVELWHEEL-46 Assembly Instructions Manual preview
SWIVELWHEEL-46
Brand: Fast Master Products Pages: 13
Anker Technology Roav VIVA Owner'S Manual preview
Roav VIVA
Brand: Anker Technology Pages: 8
Prorack K623 Fitting Instructions Manual preview
K623
Brand: Prorack Pages: 15
TATA Motors Indigo LE Owner'S Manual & Service Book preview
Indigo LE
Brand: TATA Motors Pages: 151
Thule QUICKDRAW RACHET TIE-DOWNS 855 User Manual preview
QUICKDRAW RACHET TIE-DOWNS 855
Brand: Thule Pages: 3
Waeco Perfect Fit MBM120 Installation Instructions preview
Perfect Fit MBM120
Brand: Waeco Pages: 3

Brands by name

Popular brands

Load more brands