Hino 238 Page 476 Workshop Manual Download | Manualshive

Page: 476 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1253

P2565: Nozzle position sensor failure range (High level) (VNT actuator position sensor
signal too high)

INFORMATION

1. Technical description

•

The VNT actuator steplessly operates the nozzle via the REA (Rotary Electric Actuator) and controls turbine speed
and boost pressure.

•

The VNT actuator (REA) has a position sensor and constantly monitors the target opening and the actual opening.

•

Wiping operation is carried out when the engine is stopped and the soot, oil, and other impurities accumulated in the
vane working range are removed. Also, the turbocharger mechanical working range is checked for trouble.

2. DTC set condition

(1) DTC detection condition

•

While the engine is in operation: Always

•

While the engine is stopped: During wiping operation

(2) Judgement criteria

3. Reset condition

•

After normal operation is restored and the starter switch is on the "LOCK" position.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Engine output is restricted.

•

Cruise control function is not available.

•

Auxiliary brake function is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

•

Cruise control does not work.

•

Auxiliary brake does not work.

<Symptoms on the vehicle due to malfunction>

•

–

Item

Details (Reference)

Position sensor failure

When faulty output value from sensor continues for 1 second.

VNT controller

10

8

1

5

6

7

4

2

3

3

2

4

5

8

1

14

12

6

11

7

VNT actuator
(REA)

Engine

ECU

Power

(VNTV)

(VNTG)

CAN H

CAN L

Relay

Fuse

Battery

SAPH16F010300979

«
...
474
475
476
477
478
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: AC Schnitzer Pages: 16

Brand: Alpine Pages: 8

Brand: EUFAB Pages: 12

Brand: SnapPad Pages: 5

Brand: Inbay Pages: 20

Brand: Metra Electronics Pages: 8

Brand: Van Guard Pages: 3

Brand: Hudson Pages: 34

1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P

Brand: Havis-Shields Pages: 1

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

84 61 0 028 926

Brand: BMW Pages: 13

Brand: Roadtrek Pages: 61

Brand: EUFAB Pages: 4

Brand: Menabo Pages: 8

Brand: Seat Pages: 372

Brand: Whispbar Pages: 14

PRO-FLO XT 3527

Brand: Edelbrock Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands