manualshive.com logo in svg

Hino 238, Workshop Manual, Page: 697 / 919

Share
Download
Hino 238 Workshop Manual Download Page 697

DEF SCR SYSTEM (DCU)

5–131

1.

Disconnect the DCU 86P connector.

2.

Connect the signal check harness and use the electrical tester to
measure the resistance between the terminals of the DCU 86P
vehicle-side connector and the ground.

NO

YES

1.

Connect the DEF injector connector.

2.

Connect the signal check harness and use the electrical tester to
measure the resistance between the terminals of the DCU 86P
vehicle-side connector.

3

Inspect for short-circuit in the DEF injector harness

DMH

DML

SAPH16F020400085

Measurement 

conditions

Tester 

connections

Standard values

Starter switch: 
LOCK

DCU 86P vehicle-
side connector
DML 

–

 Ground

DMH 

–

 Ground

 

Do the measurements meet the standard value?

Go to step 4.

Repair or replace the harness.
Perform "After-inspection work" of INFOR-
MATION section.

4

Inspect disconnection of the DEF injector harness

DMH

DML

SAPH16F020400086

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments