Hino 238 Workshop Manual Download Page 142 | Manualshive

Page: 142 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–919

CHECKLIST: P200C

DTC: P200C

DPF over temperature

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Check the
DTC detected
(Engine ECU)
[Hino-DX]

Check if any DTC other than
P200C (for example
P2470,P2471) has been detected
in [Engine].

DTC other
than P0263
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Go to diagno-
sis procedure
of a related
DTC.

Go to step 2.

2

Inspect the
exhaust pipe

Check for dirt or soot in the
exhaust pipe.

Failure found:
Go to YES.

No failure
found: Go to
NO.

Go to step 3.

Go to step 6.

3

Inspect the
exhaust gas
temperature
[Hino-DX]

After replacing the filter DPR and
performing DPR manual regener-
ation, select [(OUT) Exhaust Tem-
perature] from the [Data Monitor]
Hino-DX menu, and measure the
exhaust gas temperature.

HINT
When replacing the DPR filter,
replace the burner nozzle and
clean the igniter. When replac-
ing the DPR filter, replace the
burner nozzle and clean the
igniter.

<Standard values>
Exhaust gas temperature: below
800



C

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 4.

Go to step 10.

4

Inspect the
injector [Hino-
DX]

Start the engine and select [Injec-
tion quantity] from the [Data Moni-
tor] Hino-DX menu, and measure
the amount of fuel injection.
<Measurement conditions>
Engine speed: 1,500 r/min (No
load)
Temperature: More than 80



C

<Standard values>
Injection quantity (mm

3

/st): 5.0q

or more for MT vehicles , 6.0q or
more for Allison



2200, 2500,

3500 vehicles.
Engine rotation fluctuation (r/min):
26 or less (for all type of transmis-
sion vehicles).

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 5.

Replace the
injector.
Perform "After-
inspection
work" of
INFORMA-
TION section.

«
...
140
141
142
143
144
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Reference Series

Brand: OEM Audio Pages: 29

Brand: Code 3 Pages: 8

Brand: Chevrolet Pages: 2

Brand: Honda Pages: 85

Brand: PAC Pages: 14

Brand: Kolpin Pages: 3

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brand: GARO Pages: 15

THERAPEDIC 2000

Brand: Columbia Pages: 14

Brand: Enduro Pages: 52

Brand: Westin Pages: 3

Even Brake 9400

Brand: Roadmaster Pages: 20

Brand: SuperATV Pages: 2

Brand: PMT Pages: 16

Brand: Metra Electronics Pages: 10

Brand: travall Pages: 4

Brand: Westin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands