Hino 238 Workshop Manual Download Page 121

Page: 121 / 919

ENGINE CONTROL SYSTEM (J08E)

4–898

YES

Check if the radiator outer fins are clogged or damaged.

YES

Replace the intercooler tube.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 8.

Inspect the radiator

Was any failure found?

Replace the radiator.
Perform "After-inspection work" of INFOR-
MATION section.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands