Hino 238 Page 35 Workshop Manual Download

Page: 35 / 919

ENGINE CONTROL SYSTEM (J08E)

4–812

Set the starter switch to the "LOCK" position.

Connect the common rail pressure sensor connector.

Set the starter switch to the "ON" position.

Use the electrical tester to measure the voltage between the termi-
nals of the engine ECU (signal check harness).

YES

Perform engine warm-up. (engine coolant temperature: 60



C {140



F} or more)

Stop the engine and set the starter switch to the "ON" position.

Select [Engine] and check if P119F has been detected in [Fault
Information].

YES

Inspect the signal of the common rail pressure sensor

E49

E68

E65

E64

SAPH16F010300651

Measurement

conditions

Tester connections

Standard values

Starter switch:
ON

Engine ECU (signal
check harness)
PCR1(E49)

–

PCR3(E64)

PCR1(E49)

–

PCR4(E65)

PCR2(E68)

–

PCR3(E64)

PCR2(E68)

–

PCR4(E65)

0.3

–

0.7 V

Do the measurements meet the standard value?

Go to step 5.

Replace the common rail pressure sensor.
Perform "After-inspection work" of INFOR-
MATION section.

Check the DTC detected 2(Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300652

Has DTC P119F been detected?

Replace the engine ECU.
Perform "After-inspection work" of INFOR-
MATION section.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands