Hino 238 Workshop Manual Download Page 801

Page: 801 / 919

DEF SCR SYSTEM (DCU)

5–235

Disconnect the engine coolant temperature sensor connector.

Use the electrical tester to measure the resistance between the
terminals of the engine coolant temperature sensor.

YES

Check the connection of the coolant cut off valve (DEF tank heater
valve) connector.

YES

Inspect the engine coolant temperature sensor unit

WTM-

WTM+

SAPH16F020400156

Measurement

conditions

Tester

connections

Standard values

Starter switch:
LOCK

Engine coolant
temperature
sensor
WTM +

–

WTM-



C {68



F}:

2.59

–

2.32 k





C {176



F}:

0.326

–

0.310 k



Do the measurements meet the standard value?

Go to step 7.

Replace the engine coolant temperature sen-
sor.
Perform "After-inspection work" of INFOR-
MATION section.

Inspect the coolant cut off valve (DEF tank heater valve) connector

Was any failure found?

Connect securely. Repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 8.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands