Hino 238 Workshop Manual Download Page 245 | Manualshive

Page: 245 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1022

4

Inspect for
short-circuit of
the injector
wire harness
(between
injector linked-
up connector
and injector
harness con-
nector)

Disconnect the injector harness
connector and measure the resis-
tance between each terminal in
the injector linked-up connector
(engine side) and ground.
<Tester connections>
Injector linked-up connector
(engine side)

–

Ground

#1 injector:
11

–

Ground

#2 injector:
3

–

Ground

#3 injector:
6

–

Ground

<Standard values>





The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 5.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

5

Inspect dis-
connection of
injector wire
harness

Measure the resistance between
the terminals of the #1, #2 and #3
injector harness connector.
<Tester connections>
Injector harness connector termi-
nals
#1 IJ1+

–

IJ1-

#2 IJ2+

–

IJ2-

#3 IJ3+

–

IJ3-

<Standard values>
20



C {68



F}: 0.37

–

0.57



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 7.

Go to step 6.

6

Inspect the
injector unit

Measure the resistance between
the #1

–

#3 injector terminals and

the injector bodies.
<Tester connections>
Between injector terminal and
body
<Standard values>
10 M



or more

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 7.

Replace the
injector.
Perform "After-
inspection
work" of
INFORMA-
TION section.

7

Check the
DTC detected
(Engine ECU)
[Hino-DX]

Perform engine warm-up (engine
coolant temperature: 60



C {140



F} or more), and check if P2146

has been detected in [Engine].

DTC P2146
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Replace the
engine ECU.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Procedure
completed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

DTC: P2146

Fuel injector driver circuit 1 - circuit

(circuit open)

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
243
244
245
246
247
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: RaceChip Pages: 20

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

1306 RAPID SYSTEM

Brand: Thule Pages: 8

WrapAround Windjammer

Brand: Bestop Pages: 7

Brand: EUFAB Pages: 12

Brand: Improved Racing Pages: 17

Brand: Thule Pages: 12

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Brand: Honda Pages: 330

ASENTO EV-COLC15R

Brand: ADAPT SOLUTIONS Pages: 22

Brand: Alfa Romeo Pages: 268

Brand: MovaNext Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands