Hino 238 Page 730 Workshop Manual Download

Page: 730 / 919

DEF SCR SYSTEM (DCU)

5–164

Connect the ambient air temperature sensor connector.

Disconnect the DCU 86P connector.

Connect the signal check harness and use the electrical tester to
measure the resistance between the terminals of DCU 86P vehi-
cle-side connector.

YES

Check the connection of the external resistor connector (Loose-
ness and poor contact).

YES

Inspect the ambient air temperature sensor harness

ATS-

ATSS

SAPH16F020400108

Measurement

conditions

Tester

connections

Standard values

Starter switch:
LOCK

DCU 86P vehicle-
side connector
ATSS

–

ATS-

3.7 k



Do the measurements meet the standard value?

Go to step 9.

Go to step 7.

Inspect the connector of the external resistor

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 8.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands