Hino 238 Workshop Manual Download Page 903

Page: 903 / 919

DEF SCR SYSTEM (DCU)

5–337

CHECKLIST: P2215

DTC: P2215

NOx sensor (SCR downstream) and Heater

- Circuit (Circuit open)

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

Check the
DTC detected
(DCU) [Hino-
DX]

Check if a CAN communication
system malfunction (U029E) has
been detected in [DCU].

DTC U029E
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Go to the diag-
nostic proce-
dure of a
related DTC.

Replace NOx
sensor 2 (SCR
downstream).
Perform "After-
inspection
work" of
INFORMA-
TION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands