Hino 238 Page 636 Workshop Manual Download

Page: 636 / 919

DEF SCR SYSTEM (DCU)

5–70

INSPECTION PROCEDURE: P0668

Set the starter switch to the "LOCK" position.

Connect the vehicle to Hino-DX.

Set the starter switch to the "ON" position.

Select [DCU] and check if P0668 has been detected in [Fault Infor-
mation].

YES

Check the DTC detected (DCU) [Hino-DX]

Select

DCU

SAPH16F020400048

Has DTC P0668 been detected?

Replace the DCU. (After replacing the DCU,
perform a DPR forced regeneration.)
Perform "After-inspection work" of INFOR-
MATION section.

Erase the malfunction history. Procedure
completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands