Hino 238 Workshop Manual Download Page 347 | Manualshive

Page: 347 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1124

4

Inspect the
sensor power
supply

Measure the voltage of the
exhaust gas temperature sensor
(DOC inlet) terminals.

<Tester connections>
LCZ

–

LCY

<Standard values>
4.5

–

5.5 V

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 7.

Go to step 5.

5

Inspect for
short-circuit of
the exhaust
gas tempera-
ture sensor
(DOC inlet)
harness

Connect the signal check harness
to the engine ECU (Do not con-
nect harness to the ECU) and
measure the resistance between
all the terminals of the engine
ECU (signal check harness) and
ground.

<Tester connections>
ADG9(V46)

–

Ground

ET2+(V49)

–

Ground

<Standard values>





The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 6.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

6

Inspect dis-
connection of
the exhaust
gas tempera-
ture sensor
(DOC inlet)
harness

Connect the exhaust gas temper-
ature sensor (DOC inlet) connec-
tor and measure the resistance of
the engine ECU (signal check
harness) terminals.

<Tester connections>
ADG9(V46)

–

ET2+(V49)

<Standard values>
20



C {68



F}: 13.7

–

29.8 k



50



C {122



F}: 7.13

–

13.7 k



80



C {176



F}: 4.1

–

7.13 k



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 7.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

7

Check the
DTC detected
(Engine ECU)
[Hino-DX]

1.

Warm up the engine.
(engine coolant tempera-
ture: 60



C {140



F} or more)

2.

Check if P242B has been
detected in [Engine].

DTC P242B
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Replace the
engine ECU.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Procedure
completed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

DTC: P242B

Exhaust gas temperature sensor

(DOC inlet) - rationality

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
345
346
347
348
349
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: Ignition Pages: 1

Yamaha Rhino 660

Brand: Yamaha Pages: 3

Brand: K&M Pages: 3

Brand: Condor Pages: 2

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Whispbar Pages: 15

Brand: BMW Pages: 189

Brand: Rugged Ridge Pages: 2

Brand: Subaru Pages: 44

Brand: Saab Pages: 37

Brand: Nav TV Pages: 11

Brand: Nav TV Pages: 8

Brand: Blue Bird Pages: 111

Brand: Volvo Pages: 275

EXPLORER A90095

Brand: SportRack Pages: 6

Brand: Saab Pages: 9

Brand: Geely Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands