Hino 238 Page 224 Workshop Manual Download | Manualshive

Page: 224 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1001

5

Inspect the
signal circuit of
the accelerator
sensor

Measure the resistance the termi-
nals of the accelerator sensor
vehicle-side connector.
<Tester connections>
Accelerator sensor vehicle-side
connector
SIG2

–

GND2

<Standard values>
25

–

35 k



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 8.

Go to step 6.

6

Inspect for
short-circuit of
the accelerator
sensor har-
ness

Connect the signal check har-
ness, and measure the resistance
between the terminals of the
engine ECU (signal check har-
ness) and ground.
<Tester connections>
Engine ECU (signal check har-
ness)
AVC4(V51)

–

Ground

ADG8(V65)

–

Ground

ACS2(V67)

–

Ground

<Standard values>





The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 7.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

7

Inspect dis-
connection of
the accelerator
sensor har-
ness

Connect the accelerator sensor
connector, measure the resis-
tance between the terminals of
the engine ECU (signal check
harness).
<Tester connections>
Engine ECU (signal check har-
ness)
AVC4(V51)

–

ACS2(V67)

AVC4(V51)

–

ADG8(V65)

ACS2(V67)

–

ADG8(V65)

<Standard values>
2



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 8.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

8

Check the
DTC detected
(Engine ECU)
[Hino-DX]

Check if the DTC (P2127 or
P2128) has been detected in
[Engine].

DTC (P2127
or P2128) has
been detected:
Go to YES.

No DTC has
been detected:
Go to NO.

Replace the
engine ECU.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Procedure
completed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

DTC: P2127

Accelerator pedal position sensor 2 - out of

range (Out of range low)

Inspection procedure

DTC: P2128

Accelerator pedal position sensor 2 - out of

range (Out of range high)

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
222
223
224
225
226
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: Camcar Pages: 2

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: J-Top Pages: 2

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

Brand: GARO Pages: 2

Brand: FORM FIT Pages: 2

Edge Flush Rail

Brand: Thule Pages: 12

Brand: Boyo Pages: 9

Brand: METRON Pages: 4

Brand: Road Ranger Pages: 22

Brand: CrimeStopper Pages: 1

Brand: Saab Pages: 92

Brand: A-rival Pages: 23

Brand: Cadillac Pages: 335

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands