Hino 238 Workshop Manual Download Page 388

Page: 388 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1165

Remove DPR filter and check that there is no soot leaking at the
rear edge of the DPR filter, no damage, and no other abnormality.

YES

Check the DPR filter

Damage

SAPH16F010300902

Soot leakage

SAPH16F010300903

Was any failure found?

Replace the DPR filter and the burner nozzle
and clean the igniter.
Go to step 7 after replacement.

Go to step 4.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands