manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1281

NO

YES

1.

Check the connection of the SCV connector (Looseness or short-
circuit).

NO

YES

1.

Check the connection of the common rail pressure sensor connec-
tor (Looseness or short-circuit).

NO

YES

1.

Disconnect the connector of the common rail pressure sensor.

2.

Set the starter switch to the "ON" position.

3.

Use the electrical tester to measure the voltage between the termi-
nals of the common rail pressure sensor vehicle-side connector.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 15.

15

Inspect the SCV connector

Was any failure found?

Repair or replace the faulty part, and go to
step 16.

Go to step 16.

16

Inspect the common rail pressure sensor connector

Was any failure found?

Repair or replace the faulty part, and go to
step 17.

Go to step 17.

17

Inspect the common rail pressure sensor power supply

GND2

VCC2

SAPH16F010301003

Measurement

conditions

Tester connections

Standard values

Starter switch: ON

Common rail pres-
sure sensor vehicle-
side connector
VCC2 

–

 GND2

4.5 

–

 5.5 V

Do the measurements meet the standard value?

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Hama Cup holder Operating Instruction preview
Cup holder
Brand: Hama Pages: 2
Abarth 124 SPIDER Service And Warranty Handbook preview
124 SPIDER
Brand: Abarth Pages: 36
Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Brand: Jeep Pages: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Brand: Jeep Pages: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Brand: Jeep Pages: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Brand: Jeep Pages: 525
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Brand: APS Auto Parts Specialist Pages: 3
Neuspeed 25.02.22.2 Installation Instructions preview
25.02.22.2
Brand: Neuspeed Pages: 2
GMC SIERRA 2002 Manual preview
SIERRA 2002
Brand: GMC Pages: 499
Kia Amanti Owner'S Manual preview
Amanti
Brand: Kia Pages: 290
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Brand: Chrysler Pages: 1534
Nav TV NAV-INREN Quick Manual preview
NAV-INREN
Brand: Nav TV Pages: 2
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Brand: Chevrolet Pages: 412
P-Invent Troller User Manual preview
Troller
Brand: P-Invent Pages: 4
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Brand: Ford Pages: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Brand: Intec Pages: 16
Road Ranger H392 Installation Manual preview
H392
Brand: Road Ranger Pages: 22
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Brand: Thule Pages: 12

Brands by name

Popular brands

Load more brands