Hino 238 Page 351 Workshop Manual Download

Page: 351 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1128

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

–

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

Exhaust gas temperature sensor (DOC inlet):

•

Loose/disconnected sensor or failure in sensing area (contamination, clogging or breakage)

•

Abnormal resistance of sensor

•

Short-circuit in the sensor

•

Failure in engine ECU sensor power supply

•

Disconnection or short-circuit in sensor harness

•

Irregular contact (disconnection or poor fit of connector)

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands