Hino 238 Workshop Manual Download Page 261 | Manualshive

Page: 261 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1038

CHECKLIST: P2149

DTC: P2149

Fuel injector driver circuit 2 - circuit

(circuit open)

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Inspect the
injector con-
nector

Check the connection of the injec-
tor connector (Looseness and
poor contact).

Failure found:
Go to YES.

No failure
found: Go to
NO.

Connect
securely,
repair if
needed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 2.

2

Inspect the
injector power
supply

Connect the signal check harness
to the engine ECU and measure
the voltage between the terminals
of the engine ECU (signal check
harness) and ground.
<Tester connections>
Engine ECU (signal check har-
ness)
IJ2+(E18)

–

Ground

I2+S(E38)

–

Ground

<Standard values>
At least 3/4 of battery voltage

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 3.

Go to step 7.

3

Inspect the
injector wire
harness power
supply (engine
ECU

–

injec-

tor linked-up
connector)

Measure the voltage between
each terminal in the injector
linked-up connector (ECU side)
and ground.
<Tester connections>
injector linked-up connector (ECU
side)
#4 injector: 7

–

Ground

#5 injector: 2

–

Ground

#6 injector: 10

–

Ground

<Standard values>
8 V or less

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 4.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

4

Inspect for
short-circuit of
injector wire
harness
(between
injector linked-
up connector
and injector
harness con-
nector)

Disconnect the injector harness
connector and measure the resis-
tance between each terminal in
the injector linked-up connector
(engine side) and ground.
<Tester connections>
injector linked-up connector
(engine side)
#4 injector: 7

–

Ground

#5 injector: 2

–

Ground

#6 injector: 10

–

Ground

<Standard values>





The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 5.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

«
...
259
260
261
262
263
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: UMBRA RIMORCHI Pages: 18

Brand: Vauxhall Pages: 2

Brand: Yakima Pages: 8

Brand: Car-Interface Pages: 23

Brand: RuggON Pages: 2

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Ride-Rite Air Helper Springs 2173

Brand: Firestone Pages: 4

Brand: SAN HIMA Pages: 10

Dunlop L.D02.C.M

Brand: Sumitomo Pages: 22

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Brand: RAM Pages: 13

Brand: Power Acoustik Pages: 4

Brand: Volvo Pages: 10

Brand: KLAUS Multiparking Pages: 72

Brand: ECS Electronics Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands