manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–203

INSPECTION PROCEDURE: P20A0

1.

Check the connection of the DEF pump (reverting valve) connector
(Looseness and poor contact).

NO

YES

1.

Set the starter switch to the "LOCK" position.

2.

Disconnect the DEF pump connector.

3.

Use the electrical tester to measure the resistance between the
terminals of the DEF pump (reverting valve).

NO

YES

1

Inspect the DEF pump (reverting valve) connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

2

Inspect the DEF pump (reverting valve) unit

PMV+

PMV-

SAPH16F020400131

Measurement 

conditions

Tester 

connections

Standard values

Starter switch: 
LOCK

DEF pump 
(reverting valve) 
connector
PMV+ 

–

 PMV-

23 

C {73.4 

F}: 

2.05 

–

 12.05 

Do the measurements meet the standard value?

Go to step 3.

Replace the DEF pump.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

AA Products X31 Instruction Manual preview
X31
Brand: AA Products Pages: 6
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Brand: Kolpin Outdoors Pages: 6
Schartec CR 4 Manual preview
CR 4
Brand: Schartec Pages: 2
Renault 2016 Sandero Stepway Handbook preview
2016 Sandero Stepway
Brand: Renault Pages: 183
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Brand: Menabo Pages: 8
JKS OGS125 Installation Instructions preview
OGS125
Brand: JKS Pages: 3
Prorack K577W Fitting Instructions Manual preview
K577W
Brand: Prorack Pages: 15
AL-KO AKS 1300 Operating Instructions Manual preview
AKS 1300
Brand: AL-KO Pages: 40
EUFAB 11512 Manual preview
11512
Brand: EUFAB Pages: 4
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9
HUSKY LINERS 47954 Installation Instructions preview
47954
Brand: HUSKY LINERS Pages: 4
iOttie HLCRIO138 Manual preview
HLCRIO138
Brand: iOttie Pages: 19
T-Tech FIT417 Service Bulletin preview
FIT417
Brand: T-Tech Pages: 1
Hyundai Sonata 2011 Owner'S Manual preview
Sonata 2011
Brand: Hyundai Pages: 380
Intellitronix BG6003 Installation Manual preview
BG6003
Brand: Intellitronix Pages: 11
Discount Car Stereo A2DIY-CHRY Installation Manual preview
A2DIY-CHRY
Brand: Discount Car Stereo Pages: 5
Chevrolet 2003 Blazer Owner'S Manual preview
2003 Blazer
Brand: Chevrolet Pages: 426
SSANGYONG korando C200 Service Manual preview
korando C200
Brand: SSANGYONG Pages: 37

Brands by name

Popular brands

Load more brands