Hino 238 Page 306 Workshop Manual Download

Page: 306 / 919

ENGINE CONTROL SYSTEM (J08E)

4–1083

INSPECTION PROCEDURE: P2269

Check if water has accumulated in the fuel filter.

YES

Check the connection of the water level sensor connector (Loose-
ness and poor contact).

YES

Set the starter switch to the "LOCK" position.

Disconnect the fuel filter water level sensor connector.

Connect a battery between the 12 V terminal in the fuel filter water
level sensor and the GND terminal.

Use the electrical tester to measure the voltage between the fuel
filter water level sensor SIGNAL terminal and GND terminal.

Inspect the fuel filter

Was any failure found?

Drain water out of the fuel filter.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

Inspect the fuel filter water level sensor connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 3.

Inspect the fuel filter water level sensor unit

GND

Battery

12V

SIGNAL

SAPH16F010300834

Measurement

conditions

Tester connections

Standard values

Starter switch:
LOCK

Fuel filter water
level sensor
SIGNAL

–

GND

0 V (no water)
0.6

–

0.7 V (Water

level within allow-
able range)

Do the measurements meet the standard value?

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands