manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–32

DTC: P0072

EN01H16F02040F03001012

DTC: P0072 Ambient air temperature sensor - out of range (Out of range low)

INFORMATION

1. Technical description

•

The ambient air temperature sensor inputs the outside air temperature data into the DCU to determine the heating
time when performing thawing or thermal insulation of the DEF in the DEF system pipes.

•

The ambient air temperature sensor is connected to the external resistor at 2 k

 to reduce the current flowing value

through the sensor circuit.

<Description of malfunction>

•

Ambient air temperature sensor malfunction detected. 

2. DTC set condition

(1) DTC detection condition

Starter switch ON.

(2) Judgement criteria

Ambient air temperature sensor voltage: Less than 3.4 V

3. Reset condition

•

After having restored to the normal condition.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Each temperature sensors failure diagnosis is stopped.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe)>

•

–

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

LE5

(FAT-)

LE4

LFH

LFG

(FAT+)

Exhaust gas temperature 
sensor (SCR inlet)

External
resistance

Ambient air temperature
sensor

LNM

LNN

LGJ

LGK

LQV

LQ

U

(ER-)

(ER+)

(ATS-)

(ATSS)

(HH1-)

(HH1+)

DCU

(EXT-)

(EXT+)

SAPH16F020400023

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Ignition 63-231 Quick Start preview
63-231
Brand: Ignition Pages: 1
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Brand: Mercedes-Benz Pages: 388
Standby L54 Manual preview
L54
Brand: Standby Pages: 10
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Brand: Brodit Pages: 2
Honda 2004 S2000 Owner'S Manual preview
2004 S2000
Brand: Honda Pages: 208
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Brand: Chrysler Pages: 1534
DriveRight 8156OBD Installation Manual preview
8156OBD
Brand: DriveRight Pages: 16
Whispbar K835W Fitting Instructions For Basic Carrier preview
K835W
Brand: Whispbar Pages: 63
Jaeger 12160509J Fitting Instructions Manual preview
12160509J
Brand: Jaeger Pages: 16
Edelbrock 5756 Installation Instructions preview
5756
Brand: Edelbrock Pages: 1
CSL 41802 User Manual preview
41802
Brand: CSL Pages: 8
Kuda 191090 Installation Instruction preview
191090
Brand: Kuda Pages: 3
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Brand: T.J.M. Pages: 18
Audi PXDXVW3 Quick Start Manual preview
PXDXVW3
Brand: Audi Pages: 4
Bulldog Security BulldogOne BD1 User Manual preview
BulldogOne BD1
Brand: Bulldog Security Pages: 7
Hyundai TUCSON 2022 Quick Reference Manual preview
TUCSON 2022
Brand: Hyundai Pages: 32
Quadratec QuadraTop Adventure Top 1113.00 Series Installation Manual preview
QuadraTop Adventure Top 1113.00 Series
Brand: Quadratec Pages: 20
Kia MOHAVE 2014 Owner'S Manual preview
MOHAVE 2014
Brand: Kia Pages: 417

Brands by name

Popular brands

Load more brands