Hino 238 Page 683 Workshop Manual Download

Page: 683 / 919

DEF SCR SYSTEM (DCU)

5–117

CHECKLIST: P203D

DTC: P203D

DEF tank level sensor - out of range

(Out of range high)

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

Check the
DTC detected
(Engine)
[Hino-DX]

Check if a CAN communication
system malfunction (U02A2) has
been detected in [Engine].

DTC U02A2
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Go to the diag-
nostic proce-
dure of a
related DTC.

Replace the
DEF tank level
sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands