manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–940

4

Inspect the 
exhaust gas 
temperature 
sensor (SCR 
inlet) connec-
tor

Check the connection of the 
exhaust gas temperature sensor 
(SCR inlet) connector. (Loose-
ness and poor contact)

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Connect 
securely, 
repair if 
needed.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 5.

5

Inspect the 
exhaust gas 
temperature 
sensor (SCR 
inlet)

 

1.

Check the installation of the 
exhaust gas temperature 
sensor (SCR inlet).

2.

Make sure there is no dirt or 
damage to the exhaust gas 
temperature sensor (SCR 
inlet).

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Clean the 
exhaust gas 
temperature 
sensor (SCR 
inlet) and 
install it prop-
erly.
If damaged, 
replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 6.

6

Inspect the 
exhaust gas 
temperature 
sensor (SCR 
inlet) unit

Disconnect the exhaust gas tem-
perature sensor (SCR inlet) con-
nector and measure the 
resistance between the terminals 
of the sensor. (FAT+ 

–

 FAT-)

<Standard values>
20 

C {68 

F}: 220 

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 7.

Replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

7

Check the 
DEF pipe 
(pump 

 

injector)

Check the DEF pipe (pressure 
line) and verify that there are no 
disconnections, clogging, corro-
sion, or cracks.

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Repair the 
faulty part.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 8.

DTC: P207F

Improper reductant

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Brand: Harmar Mobility Pages: 10
GARO ENTITY PRO Installation preview
ENTITY PRO
Brand: GARO Pages: 2
Atera 022 681 Manual preview
022 681
Brand: Atera Pages: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Brand: RAM Pages: 7
Hummer 2006 H2 Owner'S Manual preview
2006 H2
Brand: Hummer Pages: 502
WABCO OnSide MM16167 Maintenance Manual preview
OnSide MM16167
Brand: WABCO Pages: 52
Velleman CARS4500 User Manual preview
CARS4500
Brand: Velleman Pages: 12
Thule Kit 1312 Instructions Manual preview
Kit 1312
Brand: Thule Pages: 8
DRAGONFIRE 11-0800 Installation Instructions preview
11-0800
Brand: DRAGONFIRE Pages: 4
Front Runner LATF002 Quick Start Manual preview
LATF002
Brand: Front Runner Pages: 7
Mercedes-Benz viano 639 series Introduction Into Service Manual preview
viano 639 series
Brand: Mercedes-Benz Pages: 32
Beeper KMX250 Quick Manual preview
KMX250
Brand: Beeper Pages: 2
Bowers & Wilkins Turnoverball 1020 Installation Instructions Manual preview
Turnoverball 1020
Brand: Bowers & Wilkins Pages: 6
Valueline SVL-CARCAM11 User Manual preview
SVL-CARCAM11
Brand: Valueline Pages: 40
Toyota Camry Hybrid 2012 Warranty & Maintenance Manual preview
Camry Hybrid 2012
Brand: Toyota Pages: 62
Directed 933.SUBARU1 Installation Manual preview
933.SUBARU1
Brand: Directed Pages: 24
Mercedes-Benz A-Class 2020 Operator'S Manual preview
A-Class 2020
Brand: Mercedes-Benz Pages: 434
Blue Ox BX2711 Installation Instructions Manual preview
BX2711
Brand: Blue Ox Pages: 8

Brands by name

Popular brands

Load more brands