manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–275

5.

Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Exhaust gas purification function is declined.

•

Engine output is insufficient.

•

Vehicle does not speed up (when malfunction does not improve within 50 min.).

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

8. Estimated failure factors

•

Clogging of the DEF injector

•

Clogging of the DEF pipe

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Audiovox Prestige APS-45B Installation Manual preview
Prestige APS-45B
Brand: Audiovox Pages: 8
Volvo 1985 740 GL Owner'S Manual preview
1985 740 GL
Brand: Volvo Pages: 138
iDataLink BLADE-AL(TB)-TL2 Install Manual preview
BLADE-AL(TB)-TL2
Brand: iDataLink Pages: 9
Magneti Marelli BCF184 Installation Instructions preview
BCF184
Brand: Magneti Marelli Pages: 2
Fiat 500 L 2019 User Manual preview
500 L 2019
Brand: Fiat Pages: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Brand: Honda Pages: 6
Yuasa SmartShot Automatic 12V 1.5 Amp 5 Stage Technical Manual preview
SmartShot Automatic 12V 1.5 Amp 5 Stage
Brand: Yuasa Pages: 44
Maserati Gransport Owner'S Manual preview
Gransport
Brand: Maserati Pages: 210
OnStar liveon Owner'S Manual preview
liveon
Brand: OnStar Pages: 22
WABCO OnSide MM16167 Maintenance Manual preview
OnSide MM16167
Brand: WABCO Pages: 52
Ecco EC4210B-K Installation And Operation Instructions Manual preview
EC4210B-K
Brand: Ecco Pages: 9
Ford 2001 Explorer Owner'S Manual preview
2001 Explorer
Brand: Ford Pages: 256
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Brand: Safe Fleet Pages: 8
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Brand: Vauxhall Pages: 131
Quadratec 12057.0263 Installation Manual preview
12057.0263
Brand: Quadratec Pages: 12
AEM 30-3500 Instruction Manual preview
30-3500
Brand: AEM Pages: 27
Abrams RE-47X Installation And Operation Manual preview
RE-47X
Brand: Abrams Pages: 12
Fab Fours C3150 Installation Instructions Manual preview
C3150
Brand: Fab Fours Pages: 21

Brands by name

Popular brands

Load more brands