manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1250

5

Replace the 
VNT controller 
[Hino-DX]

 

1.

Set the starter switch to the 
"LOCK" position.

2.

Replace the VNT controller 
with a new one.

3.

Set the starter switch to the 
"ON" position.

4.

Erase the trouble history 
using the Hino-DX.

5.

Set the starter switch to the 
"LOCK" position.

6.

Set the starter switch to the 
"ON" position again.

7.

Check if P2563 has been 
detected in [Engine].

DTC P2563 
has been 
detected: Go 
to YES.

No DTC has 
been detected: 
Go to NO.

Replace the 
turbocharger.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Procedure 
completed.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

DTC: P2563

Nozzle position sensor failure range (High 

level) (VNT actuator position sensor perfor-

mance invalid)

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Brand: IAME Pages: 17
Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Brand: Mazda Pages: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Brand: Cadillac Pages: 496
Bestop WrapAround Windjammer Installation Instructions Manual preview
WrapAround Windjammer
Brand: Bestop Pages: 7
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Brand: iRacing Pages: 25
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Brand: Cadillac Pages: 522
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Brand: Nuna Pages: 17
Vauxhall Astra 2021 Owner'S Manual preview
Astra 2021
Brand: Vauxhall Pages: 259
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Brand: UAZ Pages: 112
Xingyun XY40EV Service Manual preview
XY40EV
Brand: Xingyun Pages: 74
Buick 1988 Riviera Owner'S Manual preview
1988 Riviera
Brand: Buick Pages: 161
Safe Fleet PRIME DESIGN HRR3-E-PM52 Manual preview
PRIME DESIGN HRR3-E-PM52
Brand: Safe Fleet Pages: 12
Westin 32-1660 Instructions preview
32-1660
Brand: Westin Pages: 3
Belkin F8J034 User Manual preview
F8J034
Brand: Belkin Pages: 30
Mitsubishi FTO Series Handbook preview
FTO Series
Brand: Mitsubishi Pages: 141
Whispbar K423W Fitting Instructions Manual preview
K423W
Brand: Whispbar Pages: 18
Genesis GV60 2022 Quick Reference Manual preview
GV60 2022
Brand: Genesis Pages: 29
Valeo MBHL Operating Manual preview
MBHL
Brand: Valeo Pages: 29

Brands by name

Popular brands

Load more brands