Hino 238 Page 767 Workshop Manual Download

Page: 767 / 919

DEF SCR SYSTEM (DCU)

5–201

DTC: P20A0

EN01H16F02040F03001043

DTC: P20A0 Reverting valve for DEF pump - circuit (Open load)

INFORMATION

1. Technical description

•

DCU detects the circuit failure based on the circuit voltage of the DEF pump reverting valve.

<Description of malfunction>

•

Failure of reverting valve inside DEF pump is detected.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.
DEF reverting valve is activated.

(2) Judgement criteria

DEF reverting valve voltage: > 2.7 V, and < 5 V for 2.0 sec.

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

SCR System failure lamp: ON

•

Output restriction is applied when malfunction does not improve within 500 miles.

•

Vehicle speed restriction is applied when malfunction does not improve within 2,000 miles.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient (when malfunction does not improve within 500 miles).

•

Vehicle does not speed up (when malfunction does not improve within 2,000 miles).

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

Supply module

(DEF pump)

DCU

LFQ

(PSR+)

LFR

LGD

(PSRS)

(PSR+)

(PSRS)

LFP

LGF

(PSR-)

LFJ

(PMP+)

LFL

LG8

(PMPS)

(PMP+)

(PMPS)

LFK

LGA

(PMP-)

LFM

LGB

(PMV+)

LFN

LGC

(PMV-)

LGE

LG9

SAPH16F020400130

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands