manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–983

P2123: Accelerator pedal position sensor 1 - out of range (Out of range high)

INFORMATION

1. Technical description

•

–

<Description of malfunction>

•

The accelerator sensor 1 cannot correctly sense.

2. DTC set condition

(1) Check conditions

•

Starter switch ON.

•

Battery voltage is in the range of 10 V to 16 V.

(2) Judgement criteria

•

Accelerator sensor 1 (accelerator pedal position sensor) voltage 

≥

 4.1 V (147 %)

•

Failure timer 

≥

 1 second

3. Reset condition

•

Immediately after normal operation is restored.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Cruise control function is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Cruise control does not work.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

8. Estimated failure factors

•

Harness disconnection or short-circuit

•

Malfunction of sensor 1

•

Malfunction of engine ECU

K5Z

(ACS1)

K8Z

(GND1)

(SIG1)

KRS

(AVC4)

LCS

K91

(ADG8)

(VCC2)

(GND2)

K62

K92

(ACS2)

(SIG2)

KRR

K8Y

(AVC3)

(VCC1)

LCR

K5Z

KRS

LCS

K62

KRR

LCR

K90

(ADG7)

K93

K8Z

K91

K92

K8Y

K90

K93

Accelerator
sensor 1
(accelerator pedal
position sensor)

Engine 

ECU

SAPH16F010300760

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

KC HiLiTES C Series Wiring Diagram preview
C Series
Brand: KC HiLiTES Pages: 4
Parrot CK3300 Setup Information Manual preview
CK3300
Brand: Parrot Pages: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Brand: Parrot Pages: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Brand: Parrot Pages: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Brand: Parrot Pages: 2
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Brand: Parrot Pages: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Brand: Parrot Pages: 106
UltraGauge EM Installation & Operation Manual preview
EM
Brand: UltraGauge Pages: 55
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Brand: Toyota Pages: 19
GMC 2005 Sierra Denali Owner'S Manual preview
2005 Sierra Denali
Brand: GMC Pages: 428
Mercedes-Benz GLA 250 2019 Operator'S Manual preview
GLA 250 2019
Brand: Mercedes-Benz Pages: 346
Thule Kit 1514 Instructions preview
Kit 1514
Brand: Thule Pages: 4
Masterack RM470057 Assembly Instructions preview
RM470057
Brand: Masterack Pages: 4
Over Armour Offroad KAW-SX-SDK01 Instructions For Installation And Care preview
KAW-SX-SDK01
Brand: Over Armour Offroad Pages: 5
Toyota 4Runner 2019 Quick Reference Manual preview
4Runner 2019
Brand: Toyota Pages: 52
PEUGEOT 407 2010 Manual preview
407 2010
Brand: PEUGEOT Pages: 249
Draw tite 24943 Installation Instructions preview
24943
Brand: Draw tite Pages: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Brand: Mercedes-Benz Pages: 329

Brands by name

Popular brands

Load more brands