Hino 238 Workshop Manual Download Page 609

Page: 609 / 919

DEF SCR SYSTEM (DCU)

5–43

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

8. Estimated failure factors

•

Disconnection or short-circuit in the sensor harness

•

Disconnection or poor fit of connector

•

Malfunction of the ambient air temperature sensor

•

Failure of the external resistor

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Hino 238, Workshop Manual, Page: 609 / 919

Search results

Summary of Contents for 238

Reviews: