Hino 238 Page 120 Workshop Manual Download

Page: 120 / 919

ENGINE CONTROL SYSTEM (J08E)

4–897

Check that the radiator fan (fan blades) was damaged

YES

Check if silicone oil is leaking from the fan clutch.

YES

Check that the intercooler outer fin was clogged or damaged.

YES

Check if the intercooler tubes are abnormally swollen or cracked.

Inspect the radiator fan

Was any failure found?

Replace the radiator fan.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 5.

Inspect the fan clutch

Was any failure found?

Replace the fan clutch.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 6.

Inspect the intercooler

Was any failure found?

Replace the intercooler.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 7.

Inspect the intercooler tube

Was any failure found?

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands