manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1182

8

Inspect the air 
flow sensor 
[Hino-DX]

 

1.

Set the starter switch to the 
"LOCK" position.

2.

Inspect the connection of 
the air flow sensor's connec-
tor (mating, poor contact).

3.

Replace the air flow sensor 
to the new one.

4.

Set the starter switch to the 
"ON" position.

5.

Select [Engine] on Hino-DX 
menu.

6.

Select [Suction air volume 
check] from [Check func-
tions] on the menu, and 
check that the characteristic 
air flow sensor performance 
error does not exceed 10 % 
compare with new and old 
sensors.

<Standard values>
Performance error: less than 10 
%

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 9.

Replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

9

Inspect the 
exhaust gas 
temperature 
sensor (burner 
inlet) connec-
tor

Check the connection of the 
exhaust gas temperature sensor 
(burner inlet) connector (Loose-
ness and poor contact).

Failure found: 
Go to YES.

No failure 
fond: Go to 
NO.

Connect 
securely, 
repair if 
needed.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 10.

10

Inspect the 
exhaust gas 
temperature 
sensor (burner 
inlet)

 

1.

Check the installation of the 
exhaust gas temperature 
sensor (burner inlet).

2.

Make sure there is no dirt or 
damage to the exhaust gas 
temperature sensor (burner 
inlet).

Failure found: 
Go to YES.

No failure 
fond: Go to 
NO.

Clean the 
exhaust gas 
temperature 
sensor (burner 
inlet) and 
install it prop-
erly.
If damaged, 
replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 11.

DTC: P244B

Incomplete regeneration (check sheet 1)

Inspection procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Brand: Lancia Pages: 386
Ecco Vantage 12 Series Installation And Operation Instructions preview
Vantage 12 Series
Brand: Ecco Pages: 5
Rati Armster 2 User Manual preview
Armster 2
Brand: Rati Pages: 2
Menabo JUZA Fitting Instructions Manual preview
JUZA
Brand: Menabo Pages: 12
AddSecure Asset Light Installation Manual preview
Asset Light
Brand: AddSecure Pages: 14
GAC MOTOR EMPOW Manual preview
EMPOW
Brand: GAC MOTOR Pages: 356
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Brand: FVC Pages: 8
Ford ALCON 1968 Owner'S Manual preview
ALCON 1968
Brand: Ford Pages: 52
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Brand: BENDIX Pages: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Brand: Toyota Pages: 56
RAM RAM C 2013 Specification preview
RAM C 2013
Brand: RAM Pages: 5
Car-Interface CI-RL4-MM-NP Manual preview
CI-RL4-MM-NP
Brand: Car-Interface Pages: 23
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Brand: Acura Pages: 16
Uniden BTSC1100 Owner'S Manual preview
BTSC1100
Brand: Uniden Pages: 16
Rajant 23-100068-001 Quick Start Manual preview
23-100068-001
Brand: Rajant Pages: 11
Metra Electronics 95-5810 Installation Instructions Manual preview
95-5810
Brand: Metra Electronics Pages: 8
Kia RIO 2005 General Information Manual preview
RIO 2005
Brand: Kia Pages: 25
AL-KO 605 363 Operating Instructions Manual preview
605 363
Brand: AL-KO Pages: 88

Brands by name

Popular brands

Load more brands