manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–985

NO

YES

1.

Set the starter switch to the "ON" position.

2.

Use the electrical tester to measure the voltage between the termi-
nals of the accelerator sensor 1 vehicle-side connector.

NO

YES

1.

Set the starter switch to the "LOCK" position.

2.

Use the electrical tester to measure the resistance the terminals of
the accelerator sensor vehicle-side connector.

NO

YES

Go to step 3.

Replace the accelerator sensor 1.
Perform "After-inspection work" of INFOR-
MATION section.

3

Inspect the power supply of the accelerator sensor 1

VCC1

GND1

SAPH16F010300762

Measurement

conditions

Tester connections

Standard values

Starter switch: ON

Accelerator sensor 1 
vehicle-side connector
VCC1 

–

 GND1

4.5 

–

 5.5 V

Do the measurements meet the standard value?

Go to step 4.

Go to step 5.

4

Inspect the signal circuit of the accelerator sensor 1

SIG1

GND1

SAPH16F010300763

Measurement

conditions

Tester connections

Standard values

Starter switch: 
LOCK

Accelerator sensor 
1 vehicle-side con-
nector
SIG1 

–

 GND1

25 

–

 35 k

Do the measurements meet the standard value?

Go to step 7.

Go to step 5.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

JAC S5 Workshop Manual preview
S5
Brand: JAC Pages: 70
Raven CR7 Calibration Manual preview
CR7
Brand: Raven Pages: 24
Weather Guard 237 Assembly And Installation Instructions preview
237
Brand: Weather Guard Pages: 4
Wagan 2591 User Manual preview
2591
Brand: Wagan Pages: 12
Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Brand: Harmar Mobility Pages: 10
Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Brand: Jacob Jensen Pages: 28
DAVIS 8126GD User Manual preview
8126GD
Brand: DAVIS Pages: 32
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Brand: Brodit Pages: 2
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Brand: Waeco Pages: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Brand: Tusk Pages: 2
B-Speech Sima User Manual preview
Sima
Brand: B-Speech Pages: 4
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Brand: Honda Pages: 85
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Brand: Hyundai Pages: 280
Mercedes-Benz 2015 SLK Operator'S Manual preview
2015 SLK
Brand: Mercedes-Benz Pages: 358
Hyundai SANTA FE 2020 Getting Started Manual preview
SANTA FE 2020
Brand: Hyundai Pages: 19
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Brand: Acura Pages: 6
S&B Filters 75-5053 Installation Instructions preview
75-5053
Brand: S&B Filters Pages: 4
Mazda 2016 CX3 Service Information preview
2016 CX3
Brand: Mazda Pages: 3

Brands by name

Popular brands

Load more brands