manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–133

CHECKLIST: P2048

DTC: P2048

DEF injector - disconnection 

(Disconnection (low side))

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Inspect the 
DEF injector 
connector

Check the connection of the DEF 
injector connector (Looseness 
and poor contact).

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Connect 
securely, 
repair if 
needed.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 2.

2

Inspect the 
DEF injector 
unit

Measure the resistance between 
the terminals of the DEF injector.
<Tester connections>
DEF injector
DML 

–

 DMH

<Standard values>
20 

C {68 

F}: 11.4 

–

 12.6 

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 3.

Replace the 
DEF injector.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

3

Inspect short-
circuit of the 
DEF injector 
harness

Disconnect the DCU 86P connec-
tor, connect the signal check har-
ness, and measure the resistance 
between the terminals of the DCU 
86P vehicle-side connector and 
the ground.
<Tester connections>
DCU 86P vehicle-side connector
DML 

–

 Ground

DMH 

–

 Ground

<Standard values>

 

 

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 4.

Repair or 
replace the 
harness.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

4

Inspect dis-
connection of 
the DEF injec-
tor harness

Measure the resistance of the 
wire harness and sensor between 
the DCU 86P vehicle-side con-
nector and the DEF injector.

 

1.

Connect the DEF injector 
connector.

2.

Connect the signal check 
harness, and use the electri-
cal tester to measure the 
resistance between the ter-
minals of the DCU 86P vehi-
cle-side connector.

<Tester connections>
DCU 86P vehicle-side connector
DML 

–

 DMH

<Standard values>
20 

C {68 

F}: 11.4 

–

 12.6 

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 5.

Repair or 
replace the 
harness.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Pacbrake 10475 Installation Manual preview
10475
Brand: Pacbrake Pages: 9
Jeep Compass Owner'S Handbook Manual preview
Compass
Brand: Jeep Pages: 322
Jeep Compass Repair Manual preview
Compass
Brand: Jeep Pages: 341
Jeep Compass Operating Information Manual preview
Compass
Brand: Jeep Pages: 310
Jeep Compass Information Manual preview
Compass
Brand: Jeep Pages: 189
Jeep Compass Review preview
Compass
Brand: Jeep Pages: 26
Jeep Compass Overview preview
Compass
Brand: Jeep Pages: 21
Jabra SP200 - QUICKSTART GUIDE 1 Quick Start Manual preview
SP200 - QUICKSTART GUIDE 1
Brand: Jabra Pages: 2
Jabra BT150 - Headset - Over-the-ear Quick Start Manual preview
BT150 - Headset - Over-the-ear
Brand: Jabra Pages: 2
Kathrein DDA Series User Manual preview
DDA Series
Brand: Kathrein Pages: 7
Kargo Master 4A82T Installation Manual preview
4A82T
Brand: Kargo Master Pages: 6
Eaton Green Motion DC 66 User Manual preview
Green Motion DC 66
Brand: Eaton Pages: 18
Atera 022 681 Manual preview
022 681
Brand: Atera Pages: 10
RAM 4500 CHASSIS CAB 2012 Specification preview
4500 CHASSIS CAB 2012
Brand: RAM Pages: 7
Volvo V70XC Cross country 1998 Owner'S Manual preview
V70XC Cross country 1998
Brand: Volvo Pages: 262
Ford TRANSIT CUSTOM Quick Reference Manual preview
TRANSIT CUSTOM
Brand: Ford Pages: 15
Honda 08L04-SZA-100 Installation Instructions preview
08L04-SZA-100
Brand: Honda Pages: 3
PUTCO 1951 Series Instruction Manual preview
1951 Series
Brand: PUTCO Pages: 3

Brands by name

Popular brands

Load more brands