Hino 238 Workshop Manual Download Page 886 | Manualshive

Page: 886 / 919

background image

DEF SCR SYSTEM (DCU)

5–320

CHECKLIST: P2209

DTC: P2209

NOx sensor (SCR upstream)

- Heater performance

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Inspect the
NOx sensor 1
(SCR
upstream)
connector

Check the connection of the NOx
sensor (SCR upstream) connec-
tor (Looseness and poor contact).

Failure found:
Go to YES.

No failure
found: Go to
NO.

Connect
securely,
repair if
needed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 2.

2

Inspect the
NOx sensor 1
harness (CAN
communica-
tion line)

Disconnect the NOx sensor 1
connector, use the oscilloscope to
measure the voltage between the
terminals of the NOx sensor 1
vehicle-side connector.
<Tester connections>
NOx sensor 1 vehicle-side con-
nector
CANH

–

CANL

<Standard values>
0

–

5 V pulse waveform

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 3.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

3

Inspect the
NOx sensor 1
harness (GND
line)

Measure the resistance between
the terminals of the NOx sensor 1
vehicle-side connector.
<Tester connections>
NOx sensor 1 vehicle-side con-
nector
GND

–

GND

<Standard values>
Continuity

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 4.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

4

Inspect the
NOx sensor 1
harness
(power supply
line)

Measure the voltage between the
terminals of the NOx sensor 1
vehicle-side connector.
<Tester connections>
NOx sensor 1 vehicle-side con-
nector
VCC

–

GND

<Standard values>
9

–

16 V

The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 5.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

5

Inspect the
exhaust gas
temperature
sensor (SCR
inlet) connec-
tor

Check the connection of the
exhaust gas temperature sensor
(SCR inlet) connector (Looseness
and poor contact).

Failure found:
Go to YES.

No failure
found: Go to
NO.

Connect
securely,
repair if
needed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 6.

«
...
884
885
886
887
888
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: ZAPTEC Pages: 240

Brand: Camoplast Pages: 60

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: LAMBORGHINI Pages: 48

Brand: Trailboss Pages: 8

Brand: Mazda Pages: 122

Brand: Pyle Pages: 2

Portable Car Umbrella

Brand: Mynew Pages: 5

Brand: Kargo Master Pages: 18

Brand: Yakima Pages: 10

Brand: ICON Pages: 4

MagicWatch MW150

Brand: Waeco Pages: 144

Brand: Brodit Pages: 2

Brand: RAWLINK Pages: 25

Brand: Quadratec Pages: 8

Brand: PEUGEOT Pages: 67

Brand: Honda Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands