Hino 238 Workshop Manual Download Page 193

Page: 193 / 919

ENGINE CONTROL SYSTEM (J08E)

4–970

DTC: P2103

EN01H16F01030F03001125

P2103: DC motor for intake throttle valve - circuit (Short circuit (circuit high))

INFORMATION

1. Technical description

•

The diesel throttle (intake throttle) is of the butterfly type by DC motor driving.

<Description of malfunction>

•

Detection of +B short-circuit in the diesel throttle harness.

2. DTC set condition

(1) DTC detection condition

•

Battery voltage is in the range of 8 V to 16 V.

•

There must be no disconnection in the harness that is connected to the intake throttle.

(2) Judgement criteria

•

The diesel throttle (intake throttle) drive current has continued to be above 12 A for 112 msec.

3. Reset condition

•

After normal operation is restored and engine is restarted after engine stall.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Engine output is restricted.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

<Symptoms on the vehicle due to malfunction>

•

–

6. Pre-inspection work

•

Check that the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check that no DTC is stored after test drive.

Common rail
pressure sensor

LD8

(MOT-)

LC0

(MOT+)

(MOT-)

LD4

(VCC)

(PCR+)

LD6

KRQ

(SIG1)

(DTS1)

LD9

LCC

(SIG2)

(DTS2)

LD5

KRB

(GND)

(AGD3)

LD7

LBZ

(MOT+)

KRE

LLJ

VCC2

GND1

SIG1

VCC1

GND2

SIG2

Engine

ECU

(AVC2)

Diesel throttle
(Intake throttle
valve)

SAPH16F010300750

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands