Hino 238 Workshop Manual Download Page 14

Page: 14 / 919

ENGINE CONTROL SYSTEM (J08E)

4–791

Set the starter switch to the "ON" position.

Select [Engine] and check if P081B has been detected in [Fault
Information].

YES

Check the DTC detected (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300638

Has DTC P081B been detected?

Replace the engine ECU.
Perform "After-inspection work" of INFOR-
MATION section.

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Hino 238, Workshop Manual, Page: 14 / 919

Search results

Summary of Contents for 238

Reviews: