Hino 238 Page 595 Workshop Manual Download | Manualshive

Page: 595 / 919

background image

DEF SCR SYSTEM (DCU)

5–29

9

Inspect dis-
connection of
the ambient air
temperature
sensor har-
ness

Measure the resistance between
the terminals of the DCU 86P
vehicle-side connector.

1.

Connect the ambient air
temperature sensor connec-
tor.

2.

Disconnect the DCU 86P
connector from DCU. Con-
nect the signal check har-
ness to measure the
resistance between the ter-
minals of the DCU 86P vehi-
cle-side connector.

<Tester connections>
DCU 86P vehicle-side connector
ATSS

–

ATS-

<Standard values>
25



C {77



F}: 3.7 k



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 10.

Repair or
replace the
harness.
Perform "After-
inspection
work" of
INFORMA-
TION section.

10

Inspect the
engine cool-
ant tempera-
ture sensor
connector

Check the connection of the
engine coolant temperature sen-
sor connector (Looseness and
poor contact).

Failure found:
Go to YES.

No failure
found: Go to
NO.

Connect
securely,
repair if
needed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 11.

11

Inspect the
engine cool-
ant tempera-
ture sensor

1.

Check the installation of the
engine coolant temperature
sensor.

2.

Make sure there is no dirt or
damage to the engine cool-
ant temperature sensor.

Failure found:
Go to YES.

No failure
found: Go to
NO.

Clean the
engine cool-
ant tempera-
ture sensor
and install it
properly.
If damaged,
replace the
engine cool-
ant tempera-
ture sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

Go to step 12.

12

Inspect the
engine cool-
ant tempera-
ture sensor
unit

Measure the resistance between
the terminals of the engine cool-
ant temperature sensor.
<Tester connections>
Engine coolant temperature sen-
sor
WTM+

–

WTM-

<Standard values>
20



C {68



F}: 2.59

–

2.32 k



80



C {176



F}: 0.326

–

0.310 k



The measure-
ments meet
the standard
value: Go to
YES.

The measure-
ments do not
meet the stan-
dard value: Go
to NO.

Go to step 13.

Replace the
engine cool-
ant tempera-
ture sensor.
Perform "After-
inspection
work" of
INFORMA-
TION section.

DTC: P0071

Ambient air temperature sensor - rationality

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

«
...
593
594
595
596
597
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

Brand: Camcar Pages: 2

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: Dacia Pages: 238

Brand: RAM Pages: 616

Brand: Nav TV Pages: 9

Brand: Honda Pages: 81

Brand: Volvo Pages: 10

Electra 225 1965

Brand: Buick Pages: 914

Brand: Brodit Pages: 2

Brand: Cadillac Pages: 529

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands