manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1000

CHECKLIST: P2127 and P2128

DTC: P2127

Accelerator pedal position sensor 2 - out of 

range (Out of range low)

Inspection procedure

DTC: P2128

Accelerator pedal position sensor 2 - out of 

range (Out of range high)

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Inspect the 
accelerator 
sensor con-
nector

Check the connection of the 
accelerator sensor connector 
(Looseness and poor contact).

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Connect 
securely. 
Repair if 
needed.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 2.

2

Inspect the 
accelerator 
sensor

 

1.

Check the installation of the 
accelerator sensor.

2.

Make sure there is no dirt or 
damage to the accelerator 
sensor.

Failure found: 
Go to YES.

No failure 
found: Go to 
NO.

Clean the 
accelerator 
sensor and 
install it prop-
erly.
If damaged, 
replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Go to step 3.

3

Inspect the 
accelerator 
sensor unit

Measure the resistance between 
the terminals of the accelerator 
sensor.
<Tester connections>
Accelerator sensor
VCC2 

–

 SIG2

VCC2 

–

 GND2

SIG2 

–

 GND2

<Standard values>
2 

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 4.

Replace the 
sensor.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

4

Inspect the 
power supply 
of the acceler-
ator sensor

Measure the voltage between the 
terminals of the accelerator sen-
sor vehicle-side connector.
<Tester connections>
Accelerator sensor vehicle-side 
connector
VCC2 

–

 GND2

<Standard values>
4.5 

–

 5.5 V

The measure-
ments meet 
the standard 
value: Go to 
YES.

The measure-
ments do not 
meet the stan-
dard value: Go 
to NO.

Go to step 5.

Go to step 6.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

UnderCover 2110 Installation Manual preview
2110
Brand: UnderCover Pages: 16
Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Brand: Bimmer Jakes Pages: 4
Waeco MagicWatch MWE800 Installation And Operating Manual preview
MagicWatch MWE800
Brand: Waeco Pages: 212
Wagan 2227-1 User Manual preview
2227-1
Brand: Wagan Pages: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Brand: Thermo King Pages: 2
Hank HKWP1100-10Q User Quick Manual preview
HKWP1100-10Q
Brand: Hank Pages: 2
Toyota Sienna 2021 Manual preview
Sienna 2021
Brand: Toyota Pages: 600
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Brand: Mitsubishi Pages: 362
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Brand: Whelen Engineering Company Pages: 2
Prorack K374 Manual preview
K374
Brand: Prorack Pages: 14
Scosche HUD580GC Manual preview
HUD580GC
Brand: Scosche Pages: 12
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Brand: IOGear Pages: 38
Aries 2051182 Installation Manual preview
2051182
Brand: Aries Pages: 3
Renault CAPTUR 2019 Vehicle Instruction Card preview
CAPTUR 2019
Brand: Renault Pages: 11
Gacell SLH 27C User Manual preview
SLH 27C
Brand: Gacell Pages: 25
Navman N-series B2+ User Manual preview
N-series B2+
Brand: Navman Pages: 27
INNO TR163 Installation Instructions preview
TR163
Brand: INNO Pages: 3
Saab 2007 9-7X Owner'S Manual preview
2007 9-7X
Brand: Saab Pages: 498

Brands by name

Popular brands

Load more brands