Hino 238 Page 152 Workshop Manual Download

Page: 152 / 919

ENGINE CONTROL SYSTEM (J08E)

4–929

INSPECTION PROCEDURE: P204F

Set the starter switch to the "LOCK" position.

Connect the vehicle to Hino-DX.

Set the starter switch to the "ON" position.

Select [Engine] and check if P204F has been detected in [Fault
Information].

YES

Check the DTC detected (Engine ECU) [Hino-DX]

Select

Engine

SAPH16F010300726

Has DTC P204F been detected?

Go to the DTC separate diagnosis of the DEF
SCR system (DCU).

Procedure completed.
Perform "After-inspection work" of INFOR-
MATION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands