manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

DEF SCR SYSTEM (DCU)

5–145

CHECKLIST: P204B

DTC: P204B

DEF pressure sensor - rationality

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

No

1

Check the 
DTC detected 
(DCU)

 

1.

Set the starter switch to the 
"LOCK" position.

2.

Connect the vehicle to Hino-
DX.

3.

After three minutes, set the 
starter switch to the "ON" 
position.

4.

Check if P204B has been 
detected in [DCU].

DTC P204B 
has been 
detected: Go 
to YES.

No DTC has 
been detected: 
Go to NO.

Procedure 
completed.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Replace the 
DEF pump.
Perform "After-
inspection 
work" of 
INFORMA-
TION section.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Hama Cup holder Operating Instruction preview
Cup holder
Brand: Hama Pages: 2
Abarth 124 SPIDER Service And Warranty Handbook preview
124 SPIDER
Brand: Abarth Pages: 36
Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Brand: kaarta Pages: 29
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Brand: Jeep Pages: 108
Dakota Digital Retrotech RTX-68D-CHG Quick Start Manual preview
Retrotech RTX-68D-CHG
Brand: Dakota Digital Pages: 4
Cadillac 2012 Escalade Hybrid Manual preview
2012 Escalade Hybrid
Brand: Cadillac Pages: 90
TATA Motors TIGOR EV 2021 Owner'S Manual preview
TIGOR EV 2021
Brand: TATA Motors Pages: 236
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Brand: Dodge Pages: 5
Edelbrock 65932 Installation Instructions preview
65932
Brand: Edelbrock Pages: 2
M7 SPEED AGS-R2 Manual preview
AGS-R2
Brand: M7 SPEED Pages: 6
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Brand: U.S. General Pages: 8
AEM 30-3500 Instruction Manual preview
30-3500
Brand: AEM Pages: 27
Havis C-DMM-3005 Installation Instructions preview
C-DMM-3005
Brand: Havis Pages: 5
TAUBENREUTHER 16-5911 Manual preview
16-5911
Brand: TAUBENREUTHER Pages: 18
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Brand: TATA Motors Pages: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Brand: PAC Pages: 5

Brands by name

Popular brands

Load more brands