Hino 238 Workshop Manual Download Page 790

Page: 790 / 919

DEF SCR SYSTEM (DCU)

5–224

Check the
DTC detected
(DCU)

Check if P20A3 has been
detected in [DCU].

DTC P20A3
has been
detected: Go
to YES.

No DTC has
been detected:
Go to NO.

Replace the
DCU.(Perform
a DPR forced
regeneration
after replace-
ment.)
Perform "After-
inspection
work" of
INFORMA-
TION section.

Procedure
completed.
Perform "After-
inspection
work" of
INFORMA-
TION section.

DTC: P20A3

Reverting valve for DEF pump - circuit

(Circuit high)

Inspection Procedure

Step

Action

Description

Judgement

Check

(Yes/No)

Yes

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Hino 238, Workshop Manual, Page: 790 / 919

Search results

Summary of Contents for 238

Reviews: