Hino 238 Page 809 Workshop Manual Download

Page: 809 / 919

DEF SCR SYSTEM (DCU)

5–243

DTC: P20B3

EN01H16F02040F03001049

DTC: P20B3 DEF tank heater valve - circuit (Circuit low)

INFORMATION

1. Technical description

•

DCU detects malfunctions based on the coolant cut off valve (DEF tank heater valve) circuit voltage.

<Description of malfunction>

•

Malfunction of coolant cut off valve is detected.

2. DTC set condition

(1) DTC detection condition

Starter switch ON.
Coolant cut off valve duty

(2) Judgement criteria

Coolant cut off valve voltage

0.66 V for 0.05 sec.

3. Reset condition

•

After having restored to the normal conditions.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

–

<Symptoms on the vehicle due to malfunction>

•

Control will not work properly if the DEF freezes.

6. Pre-inspection work

•

Check if the battery voltage is in the normal range.

7. After-inspection work

•

Clear all past DTCs.

•

Check if no DTC is stored after test drive.

8. Estimated failure factors

•

Harness disconnection or short-circuit

•

Looseness or unsteady contact of connector

•

Coolant cut off valve malfunction

Twist

DCU

Coolant cut
off valve
(DEF tank
heater valve)

LDU

(+)

LDV

LFA

(E)

(WMV+)

(WMV-)

LFB

SAPH16F020400161

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands