manualshive.com logo in svg

Hino 238, Workshop Manual

The Thule 238 Manual can be downloaded for free from manualshive.com. This comprehensive user manual provides detailed instructions on how to assemble and use the Thule 238 product. Download now to ensure a hassle-free experience while maximizing the benefits of your Thule 238.

Share
Download
background image

ENGINE CONTROL SYSTEM (J08E)

4–1017

INSPECTION PROCEDURE: P2146

1.

Check the connection of the injector connector (Looseness and
poor contact).

NO

YES

1.

Set the starter switch to the "LOCK" position.

2.

Connect the signal check harness to the engine ECU.

3.

Set the starter switch to the "ON" position.

4.

Use the electrical tester to measure the voltage between each ter-
minal in the engine ECU (signal check harness) and ground.

NO

YES

1

Inspect the injector connector

Was any failure found?

Connect securely, repair or replace if
needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

2

Inspect the injector power supply

C

E14

ECU CASE GND
(ECU MOUNTING BOLT)

E34

SAPH16F010300785

Measurement

conditions

Tester connections

Standard values

Starter switch: 
ON

Engine ECU (signal 
check harness)
IJ1+(E14) 

–

 Ground

I1+S(E34) 

–

 Ground

At least 3/4 of bat-
tery voltage

Do the measurements meet the standard value?

Go to step 3.

Go to step 7.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Feniex AM600 Instruction Manual preview
AM600
Brand: Feniex Pages: 6
Wagan 2591 User Manual preview
2591
Brand: Wagan Pages: 12
JASTEC von-S2 Instruction Manual preview
von-S2
Brand: JASTEC Pages: 12
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Brand: Mitsubishi Pages: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Brand: Cadillac Pages: 442
Ford E-Transit 2022 Manual preview
E-Transit 2022
Brand: Ford Pages: 22
Whispbar K607W Fitting Instructions Manual preview
K607W
Brand: Whispbar Pages: 14
Big Mikes Performance Parts STO N SHO SNS 144 Installation Procedures Manual preview
STO N SHO SNS 144
Brand: Big Mikes Performance Parts Pages: 7
Lincoln MKZ 2018 Quick Reference Manual preview
MKZ 2018
Brand: Lincoln Pages: 10
Volvo 164 1969 Service Manual preview
164 1969
Brand: Volvo Pages: 266
Gator GRM430EM User Manual preview
GRM430EM
Brand: Gator Pages: 6
Curt Manufacturing 58963 Installation Manual preview
58963
Brand: Curt Manufacturing Pages: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Brand: Whispbar Pages: 112
Arrista SG8-19 Installation Manual preview
SG8-19
Brand: Arrista Pages: 2
Brodit ProClip 833995 Manual preview
ProClip 833995
Brand: Brodit Pages: 2
Revelation lnd-10716 Installation Instructions preview
lnd-10716
Brand: Revelation Pages: 4
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Brand: Kleinn Air Horns Pages: 33
Hamron 012463 Operating Instructions Manual preview
012463
Brand: Hamron Pages: 6

Brands by name

Popular brands

Load more brands