Hino 238 Workshop Manual Download Page 483 | Manualshive

Page: 483 / 919

background image

ENGINE CONTROL SYSTEM (J08E)

4–1260

DTC: P259E

EN01H16F01030F03001154

P259E: Nozzle operating range failure -NARROW (VNT actuator wiping error (too narrow
range))

INFORMATION

1. Technical description

•

The VNT actuator steplessly operates the nozzle via the REA (Rotary Electric Actuator) and controls turbine speed
and boost pressure.

•

The VNT actuator (REA) has a position sensor and constantly monitors the target opening and the actual opening.

•

Wiping operation is carried out when the engine is stopped and the soot, oil, and other impurities accumulated in the
vane working range are removed. Also, the turbocharger mechanical working range is checked for trouble.

<Description of malfunction>

•

–

2. DTC set condition

(1) DTC detection condition

•

While the engine is in operation: Always

•

While the engine is stopped: During wiping operation

(2) Judgement criteria

3. Reset condition

•

After normal operation is restored and the starter switch is on the "LOCK" position.

4. Indication, warning or system control regulation when the DTC is set.

•

MIL: ON

•

Diag lamp: OFF

•

Engine output is restricted.

•

Cruise control function is not available.

•

Auxiliary brake function is not available.

5. Symptoms on the vehicle when the DTC is set

<Symptoms on the vehicle due to backup control (fail safe function)>

•

Engine output is insufficient.

•

Cruise control does not work.

Item

Details (Reference)

1. Wiping failure

When a wiping operating range narrower than Lo range is detected 2 times.

VNT controller

10

8

1

5

6

7

4

2

3

3

2

4

5

8

1

14

12

6

11

7

VNT actuator
(REA)

Engine

ECU

Power

(VNTV)

(VNTG)

CAN H

CAN L

Relay

Fuse

Battery

SAPH16F010300985

«
...
481
482
483
484
485
...
»

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 238

Titanium Series

Brand: Fass Pages: 13

Green Motion Building

Brand: Eaton Pages: 12

MagicWatch MWE800

Brand: Waeco Pages: 212

Brand: Mazda Pages: 720

Brand: ECS Electronics Pages: 16

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: PAC Pages: 4

Brand: AC Schnitzer Pages: 16

Brand: Quadratec Pages: 8

VIEWLINE 52 MM - MOUNTING 11-09

Brand: VDO Pages: 4

Brand: Park-Daddy Pages: 22

Sprinter Side Ladder

Brand: FVC Pages: 8

Brand: Camoplast Pages: 19

Brand: KEKO Pages: 13

Stealth 4191F Series

Brand: Road Armor Pages: 5

Brand: DFI Pages: 6

Brand: Ferve Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands