Hino 238 Workshop Manual Download Page 760

Page: 760 / 919

DEF SCR SYSTEM (DCU)

5–194

INSPECTION PROCEDURE: P208C

Check the connection of the DEF pump connector (Looseness and
poor contact).

YES

Check the connection of the DCU 86P connector (Looseness and
poor contact).

YES

Inspect the DEF pump connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 2.

Inspect the DCU 86P connector

Was any failure found?

Connect securely, repair if needed.
Perform "After-inspection work" of INFOR-
MATION section.

Go to step 3.

Summary of Contents for 238
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands

Hino 238, Workshop Manual

Search results

Summary of Contents for 238

Reviews:

Related manuals for 238

Brands by name

Popular brands